Meade 2080/LX6 Instruction Manual download pdf (Page 7)

- 7 -

TELESCOPE ASSEMBLY

Use the following steps to assemble your telescope.

NOTE: If the section is not applicable to all LX200 models, it is

noted at the beginning of each section.

1. The Field Tripod

The field tripods (Figs. 2 and 3) for Meade 8", 10", and 12"

LX200 telescopes are supplied as completely assembled units,

except for the spreader bar (4, Fig. 2) and the 6 lock knobs (2

knobs for each of the 3 tripod legs) used to adjust the height of

the tripod. These knobs are packed separately for safety in

shipment.

For visual (i.e., non-photographic) observations, the drive base

(17, Fig. 1) of the telescope’s fork mount is attached directly to

the field tripod. The telescope in this way is mounted in an

“Altazimuth” (“Altitude-Azimuth,” or “vertical-horizontal”) format.

The telescope in this configuration moves along vertical and

horizontal axes, corresponding respectively to the Declination

and Right Ascension axes (explained later in this manual) in an

astronomical observing mode.

Alternately, the field tripod can be used in conjunction with the

appropriate optional equatorial wedge (

APPENDIX A

, page 25)

for long exposure astrophotography. The equatorial wedge

permits alignment of the telescope’s Polar Axis with the

Celestial Pole (or North Star).

After removing the field tripod from its shipping carton, stand

the tripod vertically, with the tripod feet down and with the tripod

still fully collapsed (see Fig. 3). Grasp two of the tripod legs

and, with the full weight of the tripod on the third leg, gently pull

the legs apart to a fully open position.

Thread in the 6 lock-knobs (2 on each tripod leg) near the foot

of each tripod leg (Fig. 2). These lock-knobs are used to fix the

height of the inner, extendible tripod leg sections.

NOTE: “Firm feel” tightening is sufficient; over-tightening may

result in stripping of the knob threads or damage to the tripod

legs and results in no additional strength.

The spreader bar (4, Fig. 2) has been removed for shipment.

To replace, first remove the threaded rod (2, Fig.2) from the

tripod head (1, Fig. 2); a small piece of plastic holds the

threaded rod in place. Remove the small plastic bag that is

stapled to the threaded rod. This bag contains the “C” clip

retainer (used below) and an extra clip.

Slide the spreader bar onto the threaded rod (note the correct

orientation as shown in Fig. 2) and position the threaded rod

back through the tripod head. Place the clip retainer ( a “C” clip)

into the slot in the threaded rod. This clip holds the threaded

rod in place. See Fig. 3.

Position the spreader bar so that the 3 arms of the spreader bar

are lined up with the 3 tripod legs.

Place the entire telescope onto the top of the tripod head, and

thread the threaded rod into the central threaded hole in the

bottom of the drive base of the telescope. Tighten the tension

knob (3, Fig. 2); firm tightening of the tension knob is sufficient

to result in rigid positioning of the tripod legs.

To vary the tripod height, loosen the 6 lock-knobs, slide the 3

inner tripod leg sections out to the desired height, and firmly re-

tighten (but do not overtighten) the 6 lock-knobs.

To collapse the tripod (after removing the telescope and

equatorial wedge, if applicable) for storage follow these steps:

• Rotate the spreader bar 60° from its assembled position,

so that one spreader bar arm is located between each

adjacent pair of tripod legs.

• At the base of the tripod is a 3-vane extension strut

system, with a circular hub at its center (7, Fig. 2). Grasp

the tripod head (1, Fig. 2) with one hand and, with the

other hand, pull directly “up” on the central hub of the

extension strut system. This operation will cause the

tripod legs to move inward to a collapsed position.

PRECAUTIONARY NOTES

• If the tripod does not seem to extend or

collapse easily, do not force the tripod legs in

or out. By following the instructions above,

the tripod will function properly, but if you are

unclear on the proper procedure, forcing the

tripod into an incorrect position may damage

the extension strut system.

• Do not overtighten the 6 lock-knobs used to

fix the inner tripod leg sections at various

heights. “Firm feel” tightening is sufficient.

• Be sure the spreader bar (4, Fig. 2) is not

upside-down on the threaded rod.

Fig. 3: Field Tripod (collapsed).

Fig. 2: LX200 Field Tripod. (1) Tripod Head; (2) Threaded

Rod; (3) Tension Knob; (4) Spreader Bar; (5) Lock Knobs;

(6) Extension Strut; (7) Tension Hub.

“C” Clip

1 2 3 4 5 6 7 8 9 10 11 12 ... 63 64

Comments to this Manuals

No comments

Meade 2080/LX6 Instruction Manual Page 7

Comments to this Manuals

Related products and manuals for Telescopes Meade 2080/LX6